Frequently Asked Questions


What is a U-value or U-factor?

U-value measures how well a product prevents heat from escaping. It is a measure of the rate of non solar heat loss or gain through a material or assembly. U-value ratings generally fall between 2.0-10.0 W/m2.K for Australian products. The rate of heat is indicated in the terms of the U-value of a window assembly which includes the effect of the frame, glass, seals and any spacers. The lower the U-value, the greater a window's resistance to heat flow and the better its insulating value. The U-value for a window takes account of the various U-values for the components making up the window, so you may see these in technical literature; UW is the value for whole window and because of its importance is usually abbreviated to U, UC is the value at the centre of glass, UF is the value for the frame.

Back To Top

What is the difference between R-value and U-value?

R-value and U-value are essentially two sides of the same coin. R-value is usually cited when discussing things such as wall and ceiling insulation values. The term does not translate well to windows and other fenestration products. That industry prefers U-values. The two are actually inversely related. The higher the R-value, the better insulated are the walls and ceilings. The lower the U-value, the better job a window does in keeping out the heat and cold.

Back To Top

What does Solar Heat Gain Co-efficient (SHGC) mean?

SHGC measures how well a product blocks heat caused by sunlight. The SHGC is the fraction of incident solar radiation admitted through a window, both directly transmitted, and absorbed and subsequently released inward. SHGC is expressed as a number between 0 and 1. The lower a window's SHGC, the less solar heat it transmits.

Back To Top

What is Visible Transmittance (VT)?

Visible transmittance measures how much light comes in through a product. It is an optical property that indicates the amount of visible light transmitted. VT is expressed as a number between 0 and 1. The higher the number, the more light is transmitted.

Back To Top

What is the difference between ANAC and NFRC ratings, and which one should I use?

The ANAC ratings have been available for many years and are based on "Australian National Average Conditions". This rating system is being replaced by a more advanced and globally acknowledged system developed by the NFRC (National Fenestration Rating Council) in the USA. Unfortunately, the building code called for its use before the "whole of house" rating software (called Accurate - for use in First Rate, BASIX, BERS, etc) was updated. The result is that there are two options available until the transition is complete. Companies can continue with ANAC ratings, and for those with NFRC ratings, as an interim measure, these have been adjusted so that they may run in the "whole of house" software packages. These will be re-rated again when the Accurate software upgrade has been completed, and the ANAC ratings will be discontinued.

Back To Top

Why do I need the air infiltration figure from my AS2047 test report for an energy rating?

Air infiltration (or leakage) is indicated on a test report and expressed as L/s m2. Heat loss and gain occur by infiltration through cracks in the window assembly. The lower the air infiltration figure, the less air will pass through the cracks in the window assembly, improving the energy rating.

Back To Top

What is Condensation Resistance (CR)?

CR measures the ability of a product to resist the formation of condensation on the interior surface of that product. The higher the rating, the better the window is at resisting condensation formation. The CR is expressed as a number between 0 and 100. Whilst this rating cannot predict condensation, it provides a method of comparing the potential of various window types.

Back To Top

What is considered a standard aluminium window frame?

Assume that aluminium frames are standard unless the manufacturer provides a Window Energy Rating (WERS) which demonstrates that better energy performance will be achieved by using the particular frame.

Back To Top

What is considered a thermally improved aluminium window frame?

An aluminium improved frame is defined as one which is broken but has a gap of less than 5.30mm between the pieces of aluminium. This may be achieved by a variety of design improvements, some (or all) of which may be present. To be classified as broken, a window must conform to the following definition by the U.S. National Fenestration Rating Council (ref: NFRC 100-2001).

Back To Top

What is considered a thermally broken aluminium window frame?

To be classified as thermally broken, a window must conform to the following definition by the U.S. National Fenestration Rating Council (ref: NFRC 100-2001).

"Thermal break: a material of low thermal conductivity that is inserted between members of high conductivity in order to reduce heat transfer. Thermal barrier material conductivity shall be no more than 0.5 W/m.K.

Thermally broken (TB) members: system members with a minimum of 5.30mm separation provided by a low-conductance material (where thermal conductivity is less than or equal to 0.5 W/m.K) or open air space between the interior and exterior surfaces. Such systems include members with exposed interior or exterior trim attached with clips and all skip/debridged systems".

Back To Top

What is spectrally selective glazing?

A coated or tinted glazing with optical properties that is transparent to some wavelengths of energy and reflective to others. Typical spectrally selective coatings are transparent to visible light and reflect short-wave and long-wave infrared radiation.

Back To Top

What effect does the window type have on energy performance?

For operating windows, the operating type has little direct effect on the U-value or SHGC of the unit, but it can have a significant effect on the air leakage and ventilation characteristics. Hinged windows, such as awnings and casements, generally have lower air leakage rates than sliding windows, either horizontal or double hung. A compressive seal and latch increases the effectiveness of the weather stripping in preventing air leakage through hinged windows.

Back To Top

Are there any recommendations I should consider to deliver comfort to my customer?

It is better to install efficient windows than to rely on heating, ventilation and air conditioning (HVAC) systems to solve thermal comfort problems. Not only do HVAC systems create non uniform interior conditions, only partly relieving thermal discomfort, but power outages on peak days can lead to extremely uncomfortable conditions.

In very cold climates, look for windows with very low U-values in order to minimise discomfort. If summer discomfort is expected look for very low SHGC values, but bear in mind that lower SHGCs lead to increased comfort in the summer at the expense of less winter solar warmth.

Back To Top

Member Login

Forgot your password?